Presvac Powervac 1800 3500 USG DOT Code Vacuum Tanker

Powervac Mini 1800, 3500 USG, Carbon Steel Tank, DOT Code Tank w/Robuschi 85 1800 CFM @ 27" Hg. Vacuum module mounted on a Kenworth T880 chassis with Cummins engine and Allison auto transmission. Code: D.O.T. 407 / 412 Vessel will be constructed and certified in conformance with the ASME Boiler and Pressure Vessel Code (Section VIII, Division 1) National Board Registered. Capacity - 3500 U.S. gallons plus 3% outage for expansion Head material - 5/16" carbon steel Shell material - 1/4" carbon steel Tank diameter - 78" outside diameter Tank length - 16’ ( shell 13’) Reinforcing - External exposed flat bar rings Design pressure (internal) - 25 p.s.i. Design pressure (external) - 15 p.s.i. (full vacuum) Hydrostatic test pressure - 37.5 p.s.i. Maximum allowable working - 25 p.s.i. pressure Operating temperature - -20oF to 200oF Overturn protection - Front, centre and rear, three (3) leg support and pads Pressure relief vent - Betts 4” stainless steel 316, 25 p.s.i. (407 / 412) Compartments - Single Baffle - One (1) half baffle, upper section of tank, welded to reinforcing pads Top manway - 20" with wingbolt closures Spill box - Around manway with 2” drain hoses, 3” sampling port inside spill box with coupling and cap Isolation valve - 6” Air operated butterfly valve between primary shut off and secondary shut off Primary shut off - 20” quick opening hatch with 12” stainless steel floatball seating against a neoprene seat, ball and seat inspection and service is external Vacuum lines - 6” Continuously grounded, wire reinforced, neoprene vacuum / pressure hose, looped to rear, no disconnecting required when dumping Liquid level indicator - Rotary float gauge with 9" stainless steel floatball, teflon seals, driverside front shell. Western Canadian Style Catwalk – OSHA type - Gripstrut material at 3 o'clock position, full length Ladder - Anti-skid. Handrail - Safety grab rail at tank top. Front hoist - 25 ton capacity-120” stroke, three stage hydraulic hoist. Full length subframe with body stops. Heavy duty hinge assemblies with grease fittings. Hoist safety prop. Rear door - Full opening, top hinged, door hydraulic up and down. Grease fittings on all moving parts. Neoprene door seal. carbon Steel. Door safety prop. Hose trays and fenders - Combination fenders on both sides of unit, stay down when tank lifts, trays closed in on ends, SS drain valves in each front tray. Mudflaps - Front and rear, anti-sail Toolbox - One (1) 36" x 18" x 20" passenger side, aluminum Suction valve - One (1) 4” air operated self closing Betts valve complete with coupling and drip cap, additional 4” manual Betts valve Internal riser pipe - 4” with deflector / wear plate Discharge valve - One (1) 6” air operated self closing Betts valve complete with coupling and drip cap, additional 6” manual Betts valve Top loading port - None Bumper - Heavy duty (407 / 412) for valve and underride protection - Anti skid steps to rear door locks Vibrator - Hydraulic, mounted on heavy duty mounting channel and heavy duty tank mounting pad. Pressure relief valve and variable speed control. Placards - Set of four (4) multi-purpose Fire extinguisher - One (1) Static ground - Ground cable, 25' with clamp Working lights – L.E.D. - Three (3) - two (2) at rear, one (1) at vacuum pump area Flashing beacon - Top, amber rotating Back up alarm - Audible, decibel rating 97 DBA Running lights – L.E.D. - Vapour proof, “Truck Lites” with all wiring in conduit, clearance lights, reflectors, junction box with clear lens. Hose hooks - Rear mounted, low for easy reach Cyclone - Small cyclone in series, size for proper blower CFM, with bottom hatch cover for cleaning, drain valve High vacuum blower - Robuschi 85 Tri-lobe - Capacity 1600 CFM - free air - Capacity 1250 CFM at 15" - Capacity 850 CFM at 24" - Maximum vacuum 27" - 1” ball valve on intake side of blower in piping for air inlet, easy reach for operator Auxiliary vacuum/pressure pump - Fruitland 500 - 350 CFM @ free Air, 27” Hg maximum vacuum, - 25 p.s.i. maximum pressure. - Four way valve for vacuum and pressure. - Check valve, oil catch muffler. - External moisture trap with 5” stainless steel floatball and 2” drain valve. - 3” air operated, isolation valve with continuous grounded vacuum lines looped to rear. No disconnecting required when dumping. Auxiliary pump drive - Air engaged 6 bolt p.t.o., hydraulic drive Manifold - Intake cooling and discharge Silencers - Cooling silencer - Discharge silencer Check valve - To prevent blower back spin Filter - Cartridge type 4-way valve - Vacuum and pressure - 6" ports - Maximum pressure 8 p.s.i. Hydraulic system - Hydraulic reservoir. Vented filler cap, filter and suction strainer, sight level tube. Hydraulic pump driven from air p.t.o. Valve bank to operate: dump body hoist, rear door, liquid ring pump, jetter, and vibrator oil pressure gauge and pressure relief valve. 3/4" drain in oil tank, hydraulic oil cooler and fans - Valve bank for blower, hoist, door, and vibrator Installation - Presvac to install on 2024 Western Star 47X tandem axle chassis w/Cummins X12 380 HP engine and Eaton Fuller RTO-14908LL Transmission. Finish - Painted tank- 1 color - Sandblasted with two (2) coats of primer paint. Two (2) coats of finish paint, Dupont Centari - acrylic urethane enamel, one (1) color. .