3000 U.S. Gallon carbon steel vacuum Unit, DOT 407/412, full opening rear door, hydraulic hoist dump mounted on a Western Star 47X chassis

Western Star 47X w/Cummins X12 380 HP engine and Eaton RTO-14908LL manual transmission. Code: D.O.T. 407 / 412 Vessel will be constructed and certified in conformance with the ASME Boiler and Pressure Vessel Code (Section VIII, Division 1) National Board Registered. Tank capacity - 3000 U.S. gallons plus 3% outage for expansion Head material - 5/16” carbon steel Shell material - 1/4” carbon steel Tank diameter - 72” OD Overall tank length - 16’-6” Reinforcing - External exposed rings Design pressure (internal) - 25 p.s.i. Design pressure (external) - 15 p.s.i. (full vacuum) Hydrostatic test pressure - 37.5 p.s.i. pressure Operating temperature - -20˚F to 200˚F Overturn protection - Front, centre and rear, three (3) leg support and pads Pressure relief vent - Betts 4” stainless steel 316, 25 p.s.i. (407 / 412) Primary shut off - 12” quick opening hatch with 9” stainless steel floatball seating against a neoprene seat, ball and seat inspection and service is external Isolation valve - 3” air operated butterfly valve between primary shut off and secondary shut off Secondary shut off - Heavy duty external moisture trap with 5” stainless steel floatball, seating against a neoprene seat, 2” quick action drain valve and hose, moisture trap capacity 28 gallons Vacuum lines - Continuously grounded, 3” wire reinforced, neoprene vacuum / pressure hose, looped to rear, no disconnecting required when dumping Vacuum pressure gauge - One (1) glycerine filled, anti shock Liquid level indicator - External arrow rotary float gauge with 9” stainless steel floatball, teflon packing and teflon seals Baffle - One (1) half baffle, upper section of tank, welded to reinforcing pads Top manway - One (1) 20” diameter manway with neoprene gasket, design pressure 50 p.s.i., hinge to the rear of tank Sampling port - 3” quick coupling and pressure relief valve Spilldam - Around 20” manway with drain hoses Walkway - Anti skid gripstrut material on passenger side Osha type enclosure - Around gripstrut walkway Grabrail - Tank top Ladder - To top manway - anti skid material Hoist - Front mounted hydraulic hoist, 20 tons capacity - Heavy duty hinges, grease fittings - Hoist safety prop, full length subframe Rear door - Full opening rear door, hydraulic operated, dual cylinders, heavy duty wingbolt closures, door safety prop Vibrator - One (1) hydraulically operated with heavy duty mounting pad Hose trays / fenders - Full length combination hose trays and fenders on each side of tank, stay in down position when tank body is raised, anti sail mudflaps, light protection caps, rear of hose trays closed. - Drain valves in each front tray Toolbox - Two (2) 36” x 18” x 18” Suction valve - One (1) 4” air operated self closing Betts valve complete with coupling and drip cap, 4” manual valve Internal riser pipe - 4” with deflector / wear plate Discharge valve - One (1) 6” air operated self closing Betts valve complete with coupling and drip cap, 6” manual valve Bumper - Heavy duty (407 / 412) for valve and underride protection - Anti skid steps to rear door locks Hose hooks - Two (2) on rear head Placards - Four (4) multi purpose Fire extinguisher - One (1) dry chemical type for hydro carbons Anti static ground - One (1) static ground cable, 25’ with clamp Lights- L.E.D. - Vapour proof lights, all wiring in conduit, “Truck “Lites, 3 lamp rear modules, junction box, 3 in row clearance lights, clearance lights and reflectors Worklights- L.E.D. - Two (2) spotlights with control switch in cab Amber beacon - Rear of tank top Back up alarm - Audible Vacuum pump - Presvac PV750, 410 CFM, 27” Hg maximum vacuum, ballast port cooling, 10 psi maximum pressure. Four way valve for vacuum and pressure. Check valve and oil catch muffler, screen cartridge, oil catch muffler with drain valve, Kamlock coupling for exhaust hose adaptor Pump drive - hydraulic - Air engaged heavy duty p.t.o. with hydraulic pump, hydraulic motor coupled to vacuum pump. Hydraulic oil reservoir complete with inlet and outlet filters, oil pressure gauge, level gauge, pressure relief valve, oil flow diffuser - Valve bank to operate: vacuum pump, hoist and door, Hydraulic oil cooler / heat exchanger Finish - All mild steel sandblasted, two (2) coats of primer, two (2) coats of finish paint, Dupont Centari - acrylic urethane enamel, one (1) colour (customer’s choice) - Painting on the cab & chassis is not included in this quote Cab is Stock White, tank and all accessory to be painted White, Cab Match