2026 Presvac Powervac 1600 Wet Unit on a 2026 Kenworth T-880, X-15 Cummins and Allison Automatic Transmission

Specifications: 3500 U.S. gallon Carbon Steel vacuum unit
Type: Truck mount - Dumping
Code: Non Code

Tank capacity - 3500 U.S. gallons plus 3% outage for expansion
- 3200USG Waste/300USG Stainless Water Tank

Head material - 5/16” Front head Stainless steel
Shell material - 1/4” Carbon Steel
Tank diameter - 72” OD
Overall tank length - 16’
Reinforcing - External exposed reinforcing rings
Design pressure (internal) - 14 p.s.i.
Design pressure (external) - 15 p.s.i. (full vacuum)
Pressure relief valves - Two (2) at 14 psi, in piping with drain hoses towards ground level

Primary shut off - 12” quick opening hatch with 9” stainless steel floatball seating against a neoprene seat, ball and
seat inspection and service is external

Isolation valve - (6”) Air operated butterfly valve between primary shut off and secondary shut off
Secondary-cyclone - Heavy duty cyclone size for proper CFM, 2” quick action drain valve and hose

Vacuum lines - (6”) Continuously grounded, wire reinforced,
neoprene vacuum / pressure hose, looped to rear,
no disconnecting required when dumping
Vacuum pressure gauges - Two (2) glycerine filled, anti shock, one on rear head

Liquid level indicator - External arrow rotary float gauge with 9” stainless
steel floatball, teflon packing and teflon seals, driverside shell

Baffle - One (1) half baffle, upper section of tank, welded to reinforcing pads

Top manway - One (1) 20” diameter manway with neoprene gasket, design pressure 50 p.s.i.

Spilldam - Around 20” manway with drain hoses, 3” sampling
port top of tank inside spill dam with coupling and cap

Walkway - Anti skid gripstrut material at 3 o’clock position, driverside Grabrail - Tank top
Ladder - To top manway - anti skid material
Osha enclosure - Around gripstrut walkway
Hoist - Front mounted hydraulic hoist, 25-ton capacity
- Heavy duty hinges, grease fittings
- Hoist safety prop, full length subframe

Rear door - Full opening rear door, hydraulic operated, dual cylinders, heavy duty wingbolt closures, wing bolts to have round ends on handles, door safety prop

Vibrator - Hydraulic operated with heavy duty mounting pad, variable speed, and relief valve

Hose trays / fenders - Full length combination hose trays and fenders on
each side of tank, stay in down position when tank body is raised, anti sail mudflaps, light protection
caps, trays closed in on end, and drains with valves in front of each tray

Toolbox - Two (2) 36” x 18” x 18” aluminum one each side, top of hose trays front mounted

Heated rear valves - Heated rear valves and tied into the WABASTO system.

Suction valve - One (1) 4” Betts valve complete with coupling and drip cap

Internal riser pipe - 4” Riser pipe with deflector plate
Discharge valve - One (1) 6” valve complete with coupling and drip cap

Bumper - I.C.C. Bumper short as possible
- Anti skid steps to rear door locks
Hose hooks - Two (2) on rear head, rub rails
Lights-L.E.D. - Vapour proof lights with all wiring in conduit,
“Truck Lites”, 3 lamp rear modules, junction box, 3
in a row clearance lights and reflectors
Worklights-L.E.D. - Two (2) spotlights with control switch in cab

- Extra lights at blower, catwalk top
Amber beacon - Rear of tank top
Back up alarm - Audible

High vacuum blower - Robuschi 85 Tri-lobe with enclosure
- Capacity 1800 CFM - free air
- Capacity 1100 CFM at 15"
- Capacity 850 CFM at 24"
- Maximum vacuum 27"
- Additional 4” ball valve in intake to regulate air and easy reach for operator
- Mounted behind cab

- Powervac type control panel, vacuum gauges, two presets, manual throttle up and down, temp gauge
for blower, light switches, and manual fan switch for the hydraulic cooler, all mounted outside at
workstation

Manifold - Intake cooling and discharge
Silencers - Cooling silencer
- Discharge silencer
Check valve - To prevent blower back spin
Filter - Cartridge type

4-way valve - Vacuum and pressure - 6" ports
- Maximum 8 p.s.i.

Wash Down System - Wash down system, 2500PSI @ 10 GPM, 200’ of
1/2” high pressure hose with electric reel, additional 50’ of 3/8” high pressure hose with 4’ lance gun,
includes ball valve to switch between hose reel and hand gun, drains and cleanouts, winterization port,
wash pump to run at the same time as blower, and additional work light for night operation, glycol
winterization tank.

One (1) 300USG stainless front water tank, site
glasses, and hydrant fill with 12” hatch cover with air gap. Water pump and hose reel installed in heated
aluminum cabinet with barn doors.
WABASTO heating unit, to keep water in front tank
warm, and rear valves.

Hydraulic drive - Air engaged p.t.o., hydraulic pump and motor,
coupling, hydraulic tank, oil cooler, gauges, filters,
pump mount, vac blower, dump and door, vibrator,
and vac pump

Back up camera - Installed and operates in reverse
Installation - 2026 KW T-880 X-15/500HP, Alison Automatic
Finish Tank Painted - Tank Painted

- Steel parts Sandblasted, two (2) coats of primer,
two (2) coats of finish paint, Dupont Centari - acrylic urethane enamel, one (1) colour
(customer’s choice)
-